The Pyne Pod Click 50K is a rechargeable prefilled pod kit with three pods in the box, and that three-pod system is the key to most faults. You keep the battery device, and you replace a pod and its refill container when that pod runs out. It is not a sealed disposable that you throw away when it stops, and it is not a kit you fill yourself with a bottle. A fault that looks like a dead device is often just a pod that is not clicked in place, a refill container that has not fed liquid into the pod, or a battery that is flat even though the OLED display still lights up on a draw.
Each edition of the kit has three different single flavours, one flavour in each pod, so a flavour fault can also be a pod fault. If one pod tastes faint and the next pod tastes full, the device is fine and the first pod is finished. If all three pods give the same fault, the device, the battery, or the way the pods are fitted is the more likely cause. That simple test, one pod against another, settles most faults on this kit before any replacement is needed.
Jump to Section
Pyne Pod Click 50K at a Glance: A Three-Pod Prefilled Kit, Not a Disposable
Three Flavours, Three Pods, One Device
Pyne Pod Click 50K Problems in One Quick Look
Fixing the Pyne Pod Click 50K, One Problem at a Time
Pyne Pod Click 50K at a Glance: A Three-Pod Prefilled Kit, Not a Disposable
| Entity / feature | What it is on the kit |
|---|---|
| Brand | Pyne Pod |
| Product | Pyne Pod Click 50K Vape Kit, also written as Pyne Pod Click 50000 in some listings |
| Device type | Rechargeable prefilled pod kit, NOT a sealed disposable, NOT user refillable |
| Puff rating | Up to 50,000 puffs for the whole kit in Regular Mode, up to 30,000 in Boost Mode, an approximate maker rating that varies with draw length and frequency |
| Battery | 750mAh built-in, rechargeable by USB-C, see the battery note below |
| Pod and refill total | 36ml in total for the whole kit, 3 x 2ml prefilled pods plus 3 x 10ml auto-refill containers, see the liquid note below |
| Nicotine strength | 20mg per ml (2 percent) nicotine salt in the listings checked, the standard strength listed, see the nicotine note below |
| Coil | Mesh coil built into each pod, not replaceable on its own |
| Flavours per kit | Three different single flavours per kit, one flavour in each pod, change flavour by swapping the pod, see the flavour note below |
| Firing | Draw activated, inhale to vape, no fire button for vaping in the listings checked |
| Draw style | Mouth to lung (MTL) in the listings checked, fixed airflow |
| Display | OLED display for battery level and power mode, plus a clear e-liquid window, see the display note below |
| Modes | Regular Mode 10W and Boost Mode 20W, switch by double-clicking the button in the setup instructions, see the mode note below |
| Pod connection | Pod pack attaches to the device magnetically from the side, refill container pushes into the base of the pod until it clicks |
| Replacement pods | Pyne Pod Click 50K replacement pod and refill packs only in the listings checked |
| TPD position | Pod chamber within the 2ml pod limit, refill container within the 10ml container limit, and 20mg per ml maximum, as set out in UK rules |
The battery note is short. VapeClub and Legion of Vapers agree on a 750mAh built-in battery, rechargeable by USB-C, with a full charge in just under 1 hour in one listing and about 45 minutes in another. This guide uses 750mAh as the working figure and a full charge of about 45 minutes to just under 1 hour as the working range, because the listings agree on the battery size and differ only a little on the charge time. The battery figure does not change any fix below, because every charging check is judged by a trusted cable and adapter and by vapour on a draw, not by the mAh figure alone.
The liquid note is short. The whole kit gives 36ml in total, made up of three pod sets, and each pod set gives 12ml, made up of one 2ml pod plus one 10ml refill container. One spec sheet lists 12ml on its own, and that figure is one pod set, not the whole kit. This guide uses 36ml as the working total for the whole kit and 12ml per pod set, and it keeps the 12ml figure visible here so it is not read as the kit total. A pod set gives up to 10,000 puffs in the listings checked, and the whole kit gives up to 50,000 puffs in Regular Mode because it holds three pod sets, not because one pod gives 50,000 puffs.
The nicotine note is short. Most listings say the pods and the refill containers are prefilled with 20mg nicotine salt. Vape Online Store says the nicotine is in the 2ml pod and the refill container is 0mg. This guide uses 20mg as the working strength for the kit, from most listings, and it keeps the 0mg refill claim visible here, because that listing gives it. The nicotine figure does not change any fix below, because every flavour and vapour check is judged by taste and vapour on a draw, not by the nicotine figure alone.
The flavour note is short. The kit comes in 27 themed editions in the listings checked, with more than 60 flavours across the range, and each edition holds three different single flavours, one flavour in each pod. Change flavour by swapping the pod, not by a switch or a twist. This is not a dual-flavour twist device, and a pod that tastes different from the last pod is normal on this kit, because each pod holds its own flavour. A pod that tastes faint, flat, or burnt is a different fault from a pod that simply tastes different.
The mode note is short. The setup instructions in VapeClub and Legion of Vapers say to switch between Regular Mode at 10W and Boost Mode at 20W by double-clicking the button. A VapeClub question and answer page says to switch mode by simply pressing the button. This guide uses double-click as the working method, from the setup instructions, and it keeps the single press claim visible here, because that page gives it. If a double-click does not change the mode on the display, try a single press, then check the display again before you assume the button is broken.
The display note is short. The kit has an OLED display for battery level and power mode, plus a clear e-liquid window for the liquid level. The display is the main way to read the battery and the mode, and the window is the main way to read the liquid. A display that lights up on a draw is enough to show the device is firing, and a display that stays dark after a full charge is a fault sign. Do not judge the liquid level by the display alone, because the display shows battery and mode, not liquid.
The cable note is short. VapeClub and Legion of Vapers say a USB-C cable is not included and is sold separately. A VapeBeat review lists one USB-C charging cable in the box. This guide keeps both claims visible here, because the listings disagree, and it does not state one version as settled. Check your box before you assume a cable is included, and use a trusted cable you know works for every charging check below.
Do not confuse this kit with the Pyne Pod Click S 30K, a different kit with a 900mAh battery, dual flavours in one pod, and up to 30,000 puffs. The Click 50K has a 750mAh battery, three single-flavour pods, and up to 50,000 puffs for the whole kit. VapeClub lists Click S 30K refill packs as compatible with the Click 50K device, so check the device name on the pack before you buy, because a pack made for the other kit is not the same as a pack made for this kit. Pods for other models or other brands do not fit this device in the same way, and forcing a wrong pod can damage the connection and cause leaking.
Note on the box: the listings checked give the box as one device, three 2ml pods, three 10ml refill containers, and a user manual. The cable is disputed, as set out in the cable note above, so check your box before you assume a cable is included.
Three Flavours, Three Pods, One Device
Check the pod, the display, and the refill container before you assume a flavour or vapour fault. On the Pyne Pod Click 50K, the pod, the display, and the refill container work as one system, so a pod fault can look like a device fault, and a battery fault can look like a pod fault.
How the Pod and Refill Work Together
The 2ml pod is auto-refilled from the 10ml refill container, so you do not fill the pod yourself with a bottle. Liquid moves from the container into the pod during use, so the pod can give vapour long after a 2ml pod alone would run out. Each pod set, one pod plus one container, can give up to 10,000 puffs, because the container refills the pod as it is used. A pod that gives almost nothing is not proof that the whole kit is finished, until you check whether its refill container is also empty and whether the other two pods still work. If all three pods are empty, the kit is finished, even if the battery device still charges and the display still lights up.
To set up a new pod, remove the seals from the pod mouthpiece and base, unscrew the refill-container cap, push the refill container into the base of the pod until it clicks, then attach the pod pack to the device magnetically from the side. Turn the kit upside down to refill faster, then wait for the auto-refill to feed liquid into the pod before the first draw. A pod that is used straight away, with no wait for the refill to reach the coil, can taste burnt, because liquid has not reached the coil evenly.
Reading the OLED Display and the Modes
The OLED display shows the battery level and the power mode, and the clear e-liquid window shows the liquid level. Regular Mode runs at 10W and gives up to 50,000 puffs for the whole kit, and Boost Mode runs at 20W and gives up to 30,000 puffs for the whole kit, because the higher power uses liquid and battery faster. Switch mode by double-clicking the button, and check the display to see that the mode has changed. If the display does not change, try a single press, as set out in the mode note above, then check the display again.
If the display lights up on a draw and the device gives vapour, the fault was not the battery. If the display stays dark after a full charge and a fresh pod test, the device needs replacement, not repeated refitting. Where the display shows a low battery, charge the device fully before you judge any other fault, because a low battery can look like a pod fault, a flavour fault, and a vapour fault all at once.
Pyne Pod Click 50K Problems in One Quick Look
| Problem | First thing to check |
|---|---|
| Not charging | USB-C cable, adapter, port, display, damage |
| Flavour fading | Liquid, pod age, draw speed, try another pod |
| Leaking / gurgling | Pod seating, pod seal, refill click, draw strength |
| Burnt taste | Liquid, pod age, draw speed, new pod rest |
| Not firing / pod not detected | Pod seating, magnetic click, connection, battery, seals, contacts |
| Fast battery drain | Draw length and frequency, mode, charging habits, pod age, device age |
| Flashing / screen trouble | Battery, pod seating, contacts, damage, display |
| Weak vapour | Battery, liquid, pod age, mode, draw length |
| Tight draw | Blocked inlets, pod seating, condensation, seals left on a new pod |
| Auto-firing / getting hot | Stop using it at once, do not charge or reuse it |
Fixing the Pyne Pod Click 50K, One Problem at a Time
The kit can stop hitting, fail to charge, leak, flash, or taste burnt when a pod, the contacts, the liquid level, the battery, or the airflow has a problem. Basic checks can help identify the cause before a pod or device replacement is needed.
Basic pod check, do this first for any problem below, unless that section tells you to stop for safety: Make sure the pod pack is fully clicked in place magnetically, with no gap and no wobble. This is also how to use the kit correctly for the first time, and how to replace a pod correctly. Wipe the pod contacts and the device contacts with a dry tissue, check the liquid level in the clear window, check the display on a draw, charge the device fully, and give a new pod a short rest before the first draw so the refill can reach the coil. If you have a fresh replacement pod and refill pack, test with it. If a fresh pod works and the old pod does not, the old pod is finished, even if the device is fine. On a new pod, remove every seal first, push the refill container into the base of the pod until it clicks, attach the pod pack magnetically from the side, turn the kit upside down to refill faster, and wait before the first draw.
If you also use the T9000 kit, see the Fumot RandM T9000 Not Working guide.
1. Pyne Pod Click 50K Not Charging
Not charging is when the device shows no sign on charge, or the battery does not last, even though it is plugged in. A charging fault is often a cable or port fault, not a dead battery on its own.
Common Causes
A weak or damaged USB-C cable, a weak wall adapter, or a laptop port that does not give enough power can all cause not charging. Lint or dust in the charging port can block the cable, and a cable that is not pushed fully in can also fail to charge. A battery that is very flat can take a short time before the display shows on charge, so a charge judged in the first minute can look like a fault. A device with port damage, or with liquid in the port, can also fail to charge.
How to Fix
Use a trusted USB-C cable you know works, and a trusted wall adapter, and plug the device in directly from a wall socket, not from a weak laptop port. This is how to charge the kit correctly, and it is the first fix for not charging. Push the cable fully into the port, check for lint or dust with a dry tissue, and look for the display on charge. Leave the device on charge and check again after a short time, rather than judging it in the first minute. Try one different trusted cable and one different trusted adapter, and if a cable works for another device but not for this kit, change the cable and the adapter together, not just one of them. The cable is disputed in the listings checked, as set out in the cable note above, so a trusted cable you already own is the right cable to test with. A full charge takes about 45 minutes to just under 1 hour in the listings checked, so judge charging by vapour and by the display, not by the clock alone.
When to Replace
Replace the cable and adapter first if the device charges with a different cable and adapter. Replace the device if it will not charge with a trusted cable and adapter, a clean port, and a full charge time, and the display shows no sign on charge.
For the lung specialists’ view on vaping, including that regulated vapes can help people stop smoking completely when used with expert support, but are not harmless and should not be used by anyone under 18, see British Thoracic Society.
2. Flavour Fading From the Pyne Pod Click 50K
Flavour fading is when taste gets weaker over time, even though the device still fires and still gives vapour. Flavour fading is different from a burnt taste, because vapour still feels smooth, only the taste is faint. On this kit, flavour fading in one pod only is a pod fault, not a device fault, because each pod holds its own flavour.
Common Causes
A pod that has been used for many puffs gives fading flavour as the coil and wick wear, even if liquid is still present. A pod low on liquid gives fading flavour first, then weak vapour, then almost nothing. Long, hard draws can also dull flavour faster, because the coil heats more than it needs to for a normal draw. A pod that has been in the device for a long time can also give fading flavour, even if it has not been used heavily.
How to Fix
Charge the device fully, then check the liquid level in the clear window. Remove the pod pack, wipe the contacts, and click the pod pack back into place magnetically, with no gap and no wobble. Take slow, steady draws, with a gap between draws, and see if flavour returns on a fresh draw. If flavour stays faint in one pod, try another pod from the kit, because a pod that tastes full proves the device is fine and the first pod is finished. This flavour fading fault is the same fault people describe as flavour going flat, and a pod that tastes different from the last pod is normal on this kit, because each pod holds a different single flavour.
When to Replace
Replace the pod and refill pack if flavour fading stays after a full charge, a liquid check, and a refit, and the pod has many puffs on it. Replace the device if flavour fading stays on a fresh pod, with a full battery and a clean, fully clicked-in pod, and the other pods in the kit taste faint in the same way.
3. Pyne Pod Click 50K Leaking or Gurgling
Leaking is when liquid appears outside the pod, on the device, or on your hands, and gurgling is when the draw sounds wet and vapour feels thin. A little condensation in the mouthpiece is not the same as a leak, and a hard pull can make both worse.
Common Causes
A pod that is not fully clicked in place magnetically, or a refill container that has not clicked into the base of the pod, can leave a gap where liquid escapes. A damaged pod seal, or a pod that has been refitted many times, can also leak. Hard pulls pull liquid into the mouthpiece faster than the coil can heat it, and that liquid shows as gurgling. A device kept upside down for a long time, or in a hot pocket or bag, can also cause leaking, because heat and pressure push liquid out of the pod.
How to Fix
Remove the pod pack and wipe the pod, the device, and the mouthpiece with a dry tissue. Push the refill container into the base of the pod until it clicks, then attach the pod pack magnetically from the side, with no gap and no wobble. Take slow, steady draws, rather than hard pulls, and keep the device upright when it is not being refilled. This leaking and gurgling fault is the same fault people describe as leaking. If the mouthpiece has condensation, wipe it dry and test again with a slow draw. Do not keep using a pod that leaks heavily, even if it still gives vapour.
When to Replace
Replace the pod and refill pack if leaking or gurgling stays after a clean refit and slow draws, and the pod seal or refill container shows damage. Replace the device if a fresh pod leaks in the same way, with a fully clicked-in pod and slow draws, and the device contacts or pod bay show damage.
4. Burnt Taste From the Pyne Pod Click 50K
Burnt taste is when vapour tastes harsh, dry, or like burnt cotton, even though the device still fires. Burnt taste is a sign that the coil is dry or worn, not a sign that the device needs a stronger draw.
Common Causes
A pod low on liquid, or a refill container that is empty, leaves the coil dry, and a dry coil burns on a draw. A new pod used straight away, with no short rest before the first draw, can also taste burnt, because liquid has not reached the coil evenly. Hard, long draws, one after another with no gap, can dry the coil faster than liquid can reach it. A pod that has been used for many puffs gives burnt taste as the coil and wick wear, even if liquid is still present.
How to Fix
Check the liquid level first, then see if the refill container is also empty. Give a new pod a rest before the first draw, so the refill can reach the coil and vapour is not burnt from a dry start. Turn the kit upside down to refill faster, then wait, and take slow, steady draws, with a gap between draws, rather than hard pulls one after another. If burnt taste stays after a rest and slow draws, the problem is the pod, not the draw.
When to Replace
Replace the pod and refill pack if the burnt taste stays after a liquid check, a rest, and slow draws, and the pod has low liquid or many puffs on it. Do not keep using a pod that tastes burnt, because a burnt coil will not recover. Replace the device if a fresh pod tastes burnt straight away, after a rest and slow draws, with a full battery and a fully clicked-in pod.
5. Pyne Pod Click 50K Not Firing or Pod Not Detected
Not firing is when you draw and get nothing, or the device seems dead even though it charges. A pod not detected fault often shows by a complete lack of vapour, with no display and no vapour on a draw.
Common Causes
A pod pack that is not fully clicked in place magnetically gives poor contact, so the device cannot detect the pod. Dirty contacts, condensation on the contacts, or a damaged pod can also cause a pod not detected fault. A battery that is very flat can leave the device dead on a draw, even if it shows a little life on charge. A seal left on a new pod blocks contact, and a refill container that has not clicked into the base of the pod can also fail to fire.
How to Fix
Charge the device fully, then remove the pod pack and wipe the contacts with a dry tissue. Check that every seal is removed from a new pod, then push the refill container into the base of the pod until it clicks, and attach the pod pack magnetically from the side, with no gap and no wobble. Take a slow, steady draw, and check if the display lights up and vapour follows. Test with a fresh pod and refill pack if you have one, because a fresh pod test settles a pod detection fault fast.
When to Replace
Replace the pod and refill pack if the device fires with a fresh pod, but not with the old pod, after a full charge, a clean refit, and a seal check. Replace the device if it will not fire with a fresh pod, a full battery, and clean contacts.
6. Fast Battery Drain on the Pyne Pod Click 50K
Fast battery drain is when the battery runs out much sooner than expected, even though the device still charges. A battery that drops in a few draws is a different fault from normal use over a day.
Common Causes
Long or frequent draws use more battery than short, occasional draws, and Boost Mode at 20W uses more power than Regular Mode at 10W, so a kit left in Boost Mode will drain faster. A battery that is charged with a weak adapter, or that is topped up for a few minutes at a time, can show a full level that falls fast. A pod that is worn, or that gives weak vapour, can make a user draw harder and longer, which uses more battery. A device that is older, or that has been charged many times, can also hold less charge than a new device.
How to Fix
Charge the device fully with a trusted wall adapter, and avoid judging battery life from a short top up. Switch to Regular Mode at 10W and check battery life over a day, rather than after a few draws, because Boost Mode at 20W will drain the battery faster by design. Take slow, steady draws, with a gap between draws, and check the pod age and liquid level, because a worn pod can make you draw more. Clean the contacts and refit the pod pack, so the device does not waste power on a poor connection. The Pyne Pod Click 50K uses a 750mAh battery in its own listings, and heavy use will drain it faster than light use, because 750mAh is a small battery for a 50,000 puff kit.
When to Replace
Replace the pod and refill pack if battery drain stays fast on a fresh pod, with a full charge and normal draws in Regular Mode, and the old pod was worn or low on liquid. Replace the device if battery drain stays fast on a fresh pod, with a full charge from a trusted adapter, clean contacts, and normal draws in Regular Mode, and the battery runs out much sooner than expected.
7. Pyne Pod Click 50K Flashing or Screen Trouble
Flashing is when the display blinks, shows a warning, or goes out, even though the device still charges. On this kit, flashing means the OLED display, because the kit has a display for battery level and power mode in the listings checked.
Common Causes
A battery low on charge can cause flashing or a low battery warning from the display, and a battery that is very flat can leave the display out. A pod pack that is not fully clicked in place gives poor contact, so the device cannot read the pod, and the display can flash or stay out. Dirty contacts, condensation on the contacts, or a damaged pod can also cause flashing. A device that has been dropped, or that shows damage, can flash even with a full battery and a fresh pod.
How to Fix
Charge the device fully with a trusted USB-C cable and adapter, and check the display again after a full charge. Remove the pod pack, wipe the contacts with a dry tissue, click the pod pack back into place magnetically, and take a slow, steady draw. See if the display lights up on a puff and the device gives vapour. If the display clears after a full charge and a clean refit, the fault was battery level or pod seating, not a broken display.
When to Replace
Replace the pod and refill pack if flashing or display trouble clears with a fresh pod, after a full charge and a clean refit. Replace the device if flashing or no display stays with a fresh pod, a full battery, and clean contacts, or if the device shows damage.
8. Weak Vapour From the Pyne Pod Click 50K
Weak vapour is when you get a thin draw, a small cloud, or a flavour that seems far away, even though the device still fires. Weak vapour is often a liquid or battery fault, not a broken device on its own.
Common Causes
A pod low on liquid gives thin vapour first, then almost nothing. A pod that has been used for many puffs, or that has been in the device for a long time, gives weak vapour as the coil and wick wear. A battery low on charge gives weak vapour, because the coil does not heat fully. A pod pack not fully clicked in place can also give weak vapour, because the device cannot read the pod fully.
How to Fix
Charge the device fully, then check the liquid level in the clear window. Remove the pod pack, wipe the contacts with a dry tissue, click the pod pack back into place magnetically, and test again. Take a slow, steady mouth to lung draw. Give a new pod a rest before the first draw, so the refill can reach the coil and vapour is not weak from a dry start. This weak vapour fault is the same fault people describe as not hitting. If weak vapour stays on a fresh pod, the problem is not the old pod alone. Check the mode on the display as well, because Regular Mode at 10W gives less vapour than Boost Mode at 20W by design.
When to Replace
Replace the pod and refill pack if weak vapour stays after a full charge, a full refit, and a test, and the pod has low liquid or many puffs on it. Replace the device if weak vapour stays on a fresh pod, with a full battery and a clean, fully clicked-in pod.
9. Tight Draw From the Pyne Pod Click 50K
Tight draw is when you have to pull hard to get vapour, or you get almost nothing even though the device still fires. This kit is a mouth to lung device with fixed airflow in the listings checked, so the draw is restricted by design, but a draw that gets much tighter than normal is a fault.
Common Causes
Blocked airflow inlets, lint or dust in the inlets, or condensation in the mouthpiece can make the draw feel tight. A pod pack that is not fully clicked in place, or a pod with a seal left on, can also block the draw. A pod low on liquid, or a pod that has been used for many puffs, can give a tight, weak draw. A battery low on charge can also give a weak, tight feeling draw, because the coil does not heat fully.
How to Fix
Remove the pod pack and check the airflow inlets for lint, dust, or liquid, and wipe them with a dry tissue. Check that every seal is removed from a new pod, then push the refill container into the base of the pod until it clicks, and attach the pod pack magnetically from the side. Wipe the mouthpiece and the pod contacts, and take a slow, steady draw, rather than a hard pull. If the draw stays tight, check the battery level, because a low battery can also give a weak, tight feeling draw.
When to Replace
Replace the pod and refill pack if the draw stays tight after cleaning, seal checks, and a full refit. Replace the device if the draw stays tight on a fresh pod, with clean inlets and a fully clicked-in pod.
10. Pyne Pod Click 50K Auto-Firing or Getting Hot
Auto-firing is when the device fires on its own, without a draw, or keeps firing after you stop drawing. Getting hot is when the device feels hot in a pocket, in a bag, or without use. This section is stop and replace only, with no fix steps that keep a faulty device in use.
Common Causes
Liquid in the pod bay, a damaged pod, or a device that has been dropped can cause auto-firing, because the draw sensor or the pod connection no longer reads correctly. Heat in a pocket or bag, or a device left in direct sunlight, can also make a device feel hot, and a device that fires on its own will also get hot from repeated firing.
How to Fix
Stop using the device at once. Do not charge it, do not draw from it, and do not try to fix it by removing and refitting pods, wiping contacts, or changing anything else. Keep it away from flammable material, and do not put it in a pocket or bag again. If it feels very hot, swollen, or smells of burning plastic, keep it away from people and pets, and follow local electronic waste rules for a damaged device.
When to Replace
Replace the device at once if it fires on its own, keeps firing after you stop drawing, or gets hot without use. Do not reuse the device, even if it stops firing for a short time, because the fault can return without warning.
FAQS (FREQUENTLY ASKED QUESTIONS)
Why is the Pyne Pod Click 50K not hitting after charging?
Check the battery level on the display, then check pod seating, contacts, and seals. A full charge does not help if the pod pack is not clicked in place magnetically, if a seal is left on a new pod, or if the pod is low on liquid. This is the answer for not hitting after charging. Charge fully, wipe the contacts, push the refill container into the base of the pod until it clicks, attach the pod pack magnetically from the side, and test with a fresh replacement pod and refill pack if you have one.
Why is the Pyne Pod Click 50K not hitting after fitting a new pod?
Remove every seal from the new pod, then push the refill container into the base of the pod until it clicks, and attach the pod pack magnetically from the side. Turn the kit upside down to refill faster, then wait for the auto-refill to feed liquid into the pod before the first draw, and take a slow, steady draw. A pod that is not clicked in place, or that has a seal left on, will not hit even if the battery is full.
How do you set up the Pyne Pod Click 50K?
Unbox the device and take the pods and refill containers out of the packaging. Remove the seals from the pod mouthpiece and base, unscrew the refill-container cap, push the refill container into the base of the pod until it clicks, then attach the pod pack to the device magnetically from the side. Turn the kit upside down to refill faster, wait for the auto-refill to feed liquid into the pod, then inhale and enjoy.
How do you change the pod on the Pyne Pod Click 50K?
Pull the old pod pack off the device. Remove every seal from the new pod, push the refill container into the base of the pod until it clicks, and attach the pod pack magnetically from the side, with no gap and no wobble. Turn the kit upside down to refill faster, wait before the first draw, then take a slow, steady draw. To change flavour, fit a different pod from the kit, because each pod holds its own single flavour.
Can you refill the Pyne Pod Click 50K pods?
No. This kit is a prefilled pod kit, not a user refillable kit. The pod and refill container are sealed, and the kit is not filled with a bottle by the user. When a pod is finished, replace it with a replacement pod and refill pack. Never open, pierce, or try to refill a sealed pod or refill container.
How long does it take to charge the Pyne Pod Click 50K?
The listings checked give a full charge in just under 1 hour in one listing and about 45 minutes in another, so this guide gives a range of about 45 minutes to just under 1 hour, not a single minute guarantee. Use a trusted USB-C cable and a trusted wall adapter, and charge until the display shows a full battery, or until vapour returns on a draw. Judge charging by vapour and by the display, not by the clock alone.
How many puffs does the Pyne Pod Click 50K give?
The Pyne Pod Click 50K gives up to 50,000 puffs for the whole kit in Regular Mode in the listings checked, also written as 50000 in some listings, and up to 30,000 puffs in Boost Mode. Each pod set gives up to 10,000 puffs. That figure is approximate, not a guarantee, and actual use varies with draw length and frequency, and with the mode used. A pod that gives weak flavour or burnt taste before that figure is finished, because coil wear and liquid level matter more than the puff number alone.
What pods work with the Pyne Pod Click 50K?
Only Pyne Pod Click 50K replacement pod and refill packs, also sold as Pyne Pod Click 50000 pods in some listings. Pods for other models or other brands do not fit this device in the same way, and forcing a wrong pod can damage the connection and cause leaking. Check the device name on the pod before you buy, and note that Click S 30K refill packs are listed as compatible in one listing, so check the pack name carefully before you buy.
Is the Pyne Pod Click 50K the same as the Pyne Pod Click S 30K?
No. The Click S 30K is a different kit with a 900mAh battery, dual flavours in one pod, and up to 30,000 puffs. The Pyne Pod Click 50K has a 750mAh battery, three single-flavour pods in the kit, and up to 50,000 puffs for the whole kit in Regular Mode. This guide is written for the Click 50K name and its own listings, and it keeps the two kits separate, because the battery, the flavour system, and the puff rating are all different.
How should you store the Pyne Pod Click 50K?
Store the device upright, in a cool, dry place, away from direct sunlight, heat, and water, and out of reach of children. Keep it out of a pocket or bag where the device can be damaged. Dispose of used pods and a finished device under local electronic waste rules, not in normal household waste.
