The HQD Glow Air 70K is a big puff prefilled pod kit with four pods in one device, and that four pod system is the key to most faults. You keep the battery device, and you replace the pods when they run out. It is not a sealed disposable that you throw away when it stops, and it is not a kit you fill yourself with a bottle. Two flavours are active at any time, and you switch between them with a slider at the base, without removing a pod. A fault that looks like a dead device is often just the wrong side selected, a pod that is not clicked in, or a refill container fitted to the wrong slot.
The OLED screen is your best early warning, because it shows battery level, liquid level, and the active flavour indicator at the same time. A screen that shows a low battery, or a liquid level that is empty on the side in use, settles most not firing and weak vapour cases before you touch a pod. A pod that is low on liquid will also show in taste and vapour before the battery runs out, because the kit holds a large total amount of liquid, but each side can still run out on its own.
This guide covers ten problems in a mixed order, starting with weak vapour, then not charging, mixed flavours and one side not working, tight draw, not firing, flashing and screen trouble, leaking and gurgling, burnt taste, fast battery drain, and auto-firing. Each section gives causes, fixes, and a clear pod or device replacement rule, so a slider mistake is not mistaken for a broken device, and a worn coil is not kept in use past its life.
Read this before you touch anything else: The HQD Glow Air 70K is a prefilled pod kit for adults aged 18 and over in the UK. Never open the battery device, never try to replace the battery, and never try to refill, pierce, or repair a sealed pod or refill container. Never charge a device that is hot, swollen, cracked, leaking heavily, or smells of burning plastic. When the checks in this guide fail, pod replacement comes first, and device replacement comes only after a fresh pod test fails. Stop using the device at once if it fires on its own, gets hot in a pocket or bag, or shows damage.
Jump to a section:
HQD Glow Air 70K at a Glance: A Four Pod Dual Flavour Kit, Not a Disposable
Four Pods, Two Flavours, One Slider
HQD Glow Air 70K Problems in One Quick Look
Fixing the HQD Glow Air 70K, One Problem at a Time
HQD Glow Air 70K at a Glance: A Four Pod Dual Flavour Kit, Not a Disposable
| Entity / feature | What it is on the HQD Glow Air 70K |
|---|---|
| Brand | HQD, Glow Air range |
| Product | HQD Glow Air 70K, also sold as HQD Glow Air 70K Prefilled Pod Kit |
| Device type | Rechargeable prefilled pod kit, NOT a sealed disposable, NOT user refillable |
| Puff rating | Up to 70,000 puffs per full setup, a maker rating under laboratory testing that varies with draw length and frequency |
| Battery | 850mAh built-in, rechargeable by USB-C in the listings checked |
| Pod and refill total | 44ml in total per full setup in the listings checked, see the breakdown note below |
| Nicotine strength | 20mg per ml (2 percent) nicotine salt in the listings checked |
| Coil | 1.1 ohm mesh coil, dual split mesh in the listings checked, built into the pod, not replaceable on its own |
| Flavours per setup | Two flavours active at any time, in two flavour pairs, four pods in total |
| Flavour switching | Base slider, switch without removing a pod, screen shows the active flavour |
| Firing | Draw activated, no firing button required in the listings checked |
| Draw style | Mouth to lung (MTL), tight draw, fixed airflow in the listings checked |
| Display | OLED screen showing battery level, liquid level, and active flavour indicator |
| Safety lock | Pocket safe lock in one listing, triple click to lock and unlock, see the note below |
| Size and weight | About 102 x 25.6 x 47mm, about 104g assembled in the listings checked |
| Replacement pods | HQD Glow Air 35K replacement pods in the listings checked |
| Charging cable | USB-C cable typically sold separately in the listings checked, use a cable you already own |
| TPD position | Pod and refill container within the 2ml pod and 10ml container limits, and 20mg per ml maximum, as set out in UK rules |
The liquid breakdown needs a clear note, because listings count the pods in different ways but agree on the total. The most detailed breakdowns give four 1ml prefilled pods plus four 10ml refill containers, for 44ml in total. Other listings give two 2ml prefilled pods plus four 10ml refill containers, also for 44ml in total. One listing gives a 2ml pod plus four 10ml tanks, which would be a different total, and this guide does not follow that single listing. This guide uses 44ml as the working total, and it keeps the pod count difference visible here. The total, not the pod count, is what matters for every fix below, because every fix checks whether liquid is left on the side in use, not how many pods hold it.
The safety lock also needs a clear note. One listing says the kit has a pocket safe lock that activates with a triple click, to prevent accidental firing in a bag or pocket. Other listings do not mention a lock at all. This guide mentions the lock only as a check to try if the device does not respond at all, and it does not present triple click as a confirmed maker instruction for every Glow Air 70K. If your device does not respond to a triple click, move on to seating, contacts, and charging checks, rather than assuming the lock is the fault.
Do not confuse this kit with a single pod HQD device, or with a HQD disposable. This kit holds four pods at once, in two flavour pairs, and it uses Glow Air 35K replacement pods. Pods for other HQD models or other brands do not fit this device in the same way, and forcing a wrong pod can damage the contacts and cause leaking. Check the device name on the pod before you buy.
Note on charging time: the listings checked for this kit do not give a single official full charge time. This guide does not give a single minute guarantee. Charge until the OLED screen shows a full battery, using a trusted cable, and judge charging by the screen, not by the clock alone.
Four Pods, Two Flavours, One Slider
Check the slider position, the screen flavour indicator, and the liquid on the side in use before you assume a flavour or vapour fault. On this kit, the slider, the screen, and the four pods work as one system, so a slider mistake can look like a pod fault, and a pod fault on one side can look like a device fault.
How the Base Slider Switches Flavours
Slide the base slider to the side you want, and the screen should show that flavour as active. You do not need to remove a pod to switch, and you should not remove a pod to switch flavours. A flavour that seems to have changed on its own is often just a slider that moved in a pocket or bag, or a slider that was moved during fitting and never moved back. Slide it firmly to the side you want, check the screen indicator, and take a slow draw before you judge the flavour.
Each flavour pair is fed by its own pods and refill containers. One side can run low while the other still tastes full, so a side that gives almost nothing is not proof that the whole setup is finished. Check the liquid on the side in use, slide to the other side, and see if that side gives full vapour. If both sides are low, the setup is finished, even if the battery device still charges and the screen still lights up.
Reading the OLED Screen and the Lock
The OLED screen shows battery level, liquid level, and the active flavour indicator in real time, in the listings checked. A screen that shows a battery number and a liquid level is not a fault. A screen that shows nothing after a full charge, a very low battery, or a liquid level that stays empty after fitting a fresh pod is the real problem. The refill containers are part of the pod assembly, so you can also look at the assembly and see if a container is empty, even before taste changes.
If the device does not respond at all, and one listing for this kit mentions a pocket safe lock, try a triple click as a single check, then move on if it makes no difference. Do not keep clicking, and do not assume a lock is present if your device does not mention it. A device that stays locked, or that does not respond after seating, contacts, and charging checks, needs a fresh pod test, not repeated clicking.
HQD Glow Air 70K Problems in One Quick Look
| Problem | First thing to check |
|---|---|
| Weak vapour | Battery, liquid on the side in use, pod age, slider position, draw length |
| Not charging | USB-C cable, adapter, port, screen charging sign, damage |
| Mixed flavours / one side not working | Slider position, screen flavour, liquid on the side in use |
| Tight draw | Blocked inlets, pod seating, condensation, seals left on a new pod |
| Not firing / pod not detected | Pod seating, contacts, battery, seals, airflow, lock check |
| Flashing / screen trouble | Battery, pod seating, contacts, damage |
| Leaking / gurgling | Pod seating, pod seal, container matching, draw strength |
| Burnt taste | Liquid on the side in use, pod age, draw speed, new pod rest |
| Fast battery drain | Draw length and frequency, charging habits, pod age, device age |
| Auto-firing / getting hot | Stop using it at once, do not charge or reuse it |
Fixing the HQD Glow Air 70K, One Problem at a Time
A HQD Glow Air 70K can stop hitting, fail to charge, leak, flash, or taste burnt when a pod, the contacts, the liquid level, the slider, the battery, or the airflow has a problem. Basic checks can help identify the cause before a pod or device replacement is needed.
Basic pod check, do this first for any problem below, unless that section tells you to stop for safety: Make sure every pod in the assembly is fully seated, with no gap and no wobble, and that each refill container matches its correct pod slot, L or R. Wipe the pod contacts and the device contacts with a dry tissue, check the liquid on the side in use, check the slider position and the screen flavour indicator, charge the device fully until the screen shows a full battery, and give a new pod a short rest before the first draw. If you have a fresh pod, test with it. If a fresh pod works and the old pod does not, the old pod is finished, even if the device is fine. On a new pod assembly, remove every seal first, including the silicone cap, the mouthpiece cover, the bottom sticker, and the pod base stickers, then slide the assembly in until it clicks into place.
If you also use the Hayati Pro Max kit, see the Hayati Pro Max 4000 Not Working guide.
1. Weak Vapour From the HQD Glow Air 70K
Weak vapour is when you get a thin draw, a small cloud, or a flavour that seems far away, even though the device still fires. On a four pod kit, weak vapour often comes from one side only, so it is easy to blame the device when the side in use is just low, worn, or not fully seated.
Common Causes
A pod low on liquid gives thin vapour first, then almost nothing. A pod that has been used for many puffs, or that has been in the device for a long time, gives weaker vapour as the coil wears. A pod that is not fully seated gives poor contact and poor airflow, so the coil heats less well. A slider left on the low side gives weak vapour on the side in use, while the other side still works. A battery low on charge gives a weaker draw on a mesh coil device, and a very short or very fast draw gives less vapour than a slow, steady draw.
How to Fix
Charge the device fully until the screen shows a full battery, then check the liquid on the side in use. Slide the base slider firmly to the side you want, check the screen flavour indicator, and take a slow, steady mouth to lung draw. Remove the pod assembly, wipe the contacts with a dry tissue, refit it until it clicks, and test again. Slide to the other side and test that side too. If the other side gives full vapour, the problem is with the side in use, not with the whole device. Give a new pod a short rest before the first draw, so the coil is fully primed and vapour is not weak from a dry start.
When to Replace
Replace the pod if weak vapour stays after a full charge, a full refit, and a test on both sides, and the side in use has low liquid or many puffs on it. Replace the device if weak vapour stays on a fresh pod, with a full battery and a clean, fully seated assembly, on both sides.
For UK evidence on vaping, including that it is much less harmful than smoking in the short and medium term but is not risk-free, and that it is an effective stop smoking aid for adults, see ASH UK.
2. HQD Glow Air 70K Not Charging
Not charging is when a USB-C cable and adapter do not raise the battery level, and the OLED screen does not show a charging sign or a rising battery level. A cable that fits a phone is not proof that it works for this device, and a screen that stays blank is not always a dead device.
Common Causes
A loose USB-C cable, a cable with a worn plug, or an adapter with too little output can fail to charge a device with a flat battery. Lint, dust, or liquid in the USB-C port can block the connection, and a low power source, such as a weak port on a laptop, can charge very slowly or not at all. A battery that is very flat after long storage can take time before the screen shows a charge. A damaged port, cable, or device will not charge at all, and a device that is hot, swollen, or cracked must not be charged.
How to Fix
Use a trusted USB-C cable you know works, and a trusted wall adapter, and plug the device in directly from a wall socket, not from a weak laptop port. Push the cable fully into the port, check for lint or dust with a dry tissue, and look for a charging sign on the OLED screen. Leave the device on charge and check the screen again after a short time, rather than judging it in the first minute. Try one different trusted cable and one different trusted adapter, and if a cable works for another device but not for this kit, change the cable and the adapter together, not just one of them.
When to Replace
Replace the cable and adapter first if the device charges with a different cable and adapter. Replace the device if it will not charge with a trusted cable and adapter, the port is clean and undamaged, and the screen shows no charging sign after a reasonable charge attempt. Do not keep charging a device that gets hot, swells, smells of burning plastic, or shows damage, and stop using it at once in that case.
3. Mixed Flavours or One Side Not Working on the HQD Glow Air 70K
Mixed flavours, or one side not working, is the most common complaint on a dual flavour kit, and it is also the most common slider mistake. The two flavours are fed by two different flavour pairs, so a taste from the wrong side, or a side that gives nothing, can come from the slider, not from a broken pod.
Common Causes
A slider left on the wrong side gives the flavour from that side, even if you expected the other flavour. A slider that moved in a pocket or bag can change the flavour without you noticing, and a slider that was never fully moved after fitting can leave the device on the old side. A pod low on liquid on one side gives little flavour on that side, while the other side still tastes full, which looks like a mixed flavour problem. A pod that is not fully seated on one side, or a refill container fitted to the wrong slot, can also give weak or mixed flavour on that side.
How to Fix
Slide the base slider firmly to the side you want, and check the screen flavour indicator before you draw. Check the liquid on the side in use, then slide to the other side and check its liquid and flavour too. Remove the pod assembly, check that each refill container matches its correct pod slot, L or R, wipe the contacts with a dry tissue, and refit the assembly until it clicks into place. If the flavour is wrong on one side only, test the other side with a slow draw, and see if the other side gives a clean flavour.
When to Replace
Replace the pod on the side that stays weak, mixed, or silent, after a slider check, a refit, and a liquid check, and after the other side gives a clean flavour. Replace the device if both sides give mixed or wrong flavour after a fresh pod test, with the slider firmly set, the assembly fully seated, and the screen showing the correct side.
4. Tight Draw From the HQD Glow Air 70K
Tight draw is when you have to pull hard to get vapour, or you get almost nothing even though the device still fires. This kit is a tight mouth to lung device with fixed airflow in the listings checked, so it should never draw like an open direct to lung device, and it should never feel like a blocked straw.
Common Causes
A blocked airflow inlet gives a hard pull, and dust, pocket lint, or liquid in the inlet can narrow the path. A pod that is not fully seated can also block the path, because the airflow does not line up correctly. A new pod with a seal left on, such as a silicone cap, a mouthpiece cover, a bottom sticker, or a pod base sticker, can block the airflow entirely. Condensation in the mouthpiece can narrow the path over time, and a very hard pull can flood the coil and make the draw worse, rather than better.
How to Fix
Remove the pod assembly and check the airflow inlets for lint, dust, or liquid, and wipe them with a dry tissue. Check that every seal is removed from a new pod, then refit the assembly until it clicks into place. Wipe the mouthpiece and the pod contacts, and take a slow, steady draw, rather than a hard pull. If the draw is tight on one side only, slide to the other side and test that side, because a pod seating fault on one side can affect only that side.
When to Replace
Replace the pod if the draw stays tight after cleaning, seal checks, and a full refit, and the other side draws normally. Replace the device if the draw stays tight on a fresh pod, with clean inlets and a fully seated assembly, on both sides.
5. HQD Glow Air 70K Not Firing or Pod Not Detected
Not firing is when you draw and get nothing, or the device seems dead even though it charges. A pod not detected fault often shows on the OLED screen, or by a complete lack of vapour, and it can look like a device fault when the pod is just not seated.
Common Causes
A pod assembly that is not fully seated gives poor contact, so the device cannot detect the pod. Dirty contacts, condensation on the contacts, or a damaged pod can also break the connection. Seals left on a new pod can block the airflow and the contacts at the same time. A battery that is flat, or a device that is locked in one listing for this kit, can also give no response. A pod that is finished, with low liquid and a worn coil, can also fail to fire.
How to Fix
Charge the device fully until the screen shows a full battery, then remove the pod assembly and wipe the contacts with a dry tissue. Check that every seal is removed from a new pod, then refit the assembly until it clicks into place. Check the slider position and the screen flavour indicator, and take a slow, steady draw. If one listing for this kit mentions a pocket safe lock, try a triple click as a single check, then move on if it makes no difference. Test with a fresh pod if you have one, because a fresh pod test settles a pod detection fault fast.
When to Replace
Replace the pod if the device fires with a fresh pod, but not with the old pod, after a full charge, a clean refit, and a seal check. Replace the device if it will not fire with a fresh pod, a full battery, clean contacts, and a fully seated assembly, and the screen shows no pod or no response on either side.
6. HQD Glow Air 70K Flashing or Screen Trouble
Flashing, or a screen that shows a warning or nothing at all, is a sign to check battery, pod seating, and damage, not a sign to keep drawing. On this kit, the OLED screen should show battery level, liquid level, and the active flavour indicator, so a blank screen, or a screen that stays on a low battery warning, is the clue.
Common Causes
A battery low on charge can cause flashing or a low battery warning on the screen, and a battery that is very flat can leave the screen blank. A pod that is not fully seated, or contacts that are dirty, can cause flashing as the device tries to detect the pod. A pod that is finished, with low liquid or a worn coil, can also cause flashing. A damaged pod, a damaged port, or a device that has been dropped or exposed to water can cause flashing that does not clear.
How to Fix
Charge the device fully with a trusted cable and adapter, and check the screen again after a full charge. Remove the pod assembly, wipe the contacts with a dry tissue, and refit it until it clicks into place. Check the slider position and the screen flavour indicator, and test both sides. If the screen shows a low battery warning that clears after a full charge, the fault was battery level, not a broken device. Do not charge a device that is hot, swollen, cracked, or leaking heavily, and stop using it at once in that case.
When to Replace
Replace the pod if flashing or screen trouble clears with a fresh pod, after a full charge and a clean refit. Replace the device if flashing or a blank screen stays with a fresh pod, a full battery, clean contacts, and a fully seated assembly, and the screen shows no normal battery or liquid level.
7. HQD Glow Air 70K Leaking or Gurgling
Leaking is when liquid appears outside the pod, on the device, or on your hands, and gurgling is when the draw sounds wet and vapour feels thin. A little condensation in the mouthpiece is not the same as a leak, and a hard pull can make both worse.
Common Causes
A pod that is not fully seated can let liquid escape around the seal, and a pod with a damaged seal or a cracked assembly can leak even when it is seated. A refill container fitted to the wrong slot, L or R, can cause liquid to transfer badly and leak. A very hard pull can flood the coil and cause gurgling, and a pod that is low on liquid can also gurgle as the coil heats unevenly. Leaving a device in a hot car, or storing it upside down for a long time, can also make leaking worse.
How to Fix
Remove the pod assembly and wipe the pod, the device, and the mouthpiece with a dry tissue. Check that each refill container matches its correct pod slot, and refit the assembly until it clicks into place, with no gap and no wobble. Take slow, steady draws, rather than hard pulls, and keep the device upright. If the mouthpiece has condensation, wipe it dry and test again with a slow draw. Do not keep using a pod that leaks heavily, even if it still gives vapour.
When to Replace
Replace the pod if leaking or gurgling stays after a clean refit, a container matching check, and slow draws, and the pod seal or assembly shows damage. Replace the device if a fresh pod leaks in the same way, with a fully seated assembly and slow draws, and the device contacts or pod bay show damage.
8. Burnt Taste From the HQD Glow Air 70K
Burnt taste is when vapour tastes harsh, dry, or like burnt cotton, even though the device still fires. Burnt taste is a sign that the coil is dry or worn, not a sign that the flavour is strong, and it should never be ignored.
Common Causes
A pod low on liquid gives a burnt taste first, because the coil heats with too little liquid to absorb. A pod that has been used for many puffs gives a burnt taste as the coil and wick wear, even if liquid is still present. A new pod that is used too soon, before the coil is fully primed, can taste burnt on the first draws. Very fast or very long draws can also dry the coil faster than liquid can reach it, especially on a tight mouth to lung device.
How to Fix
Check the liquid on the side in use, and slide to the other side if that side is low. Give a new pod a short rest before the first draw, and take slow, steady draws, with a short gap between draws, so liquid can reach the coil. Remove the pod assembly, wipe the contacts, and refit it until it clicks into place. If the burnt taste is on one side only, test the other side, because a worn coil on one side does not mean the whole setup is finished.
When to Replace
Replace the pod if the burnt taste stays after a liquid check, a rest, and slow draws, and the side in use has low liquid or many puffs on it. Do not keep using a pod that tastes burnt, because a burnt coil will not recover. Replace the device if a fresh pod tastes burnt straight away, after a rest and slow draws, with a full battery and a fully seated assembly.
9. Fast Battery Drain on the HQD Glow Air 70K
Fast battery drain is when the OLED screen shows a falling battery level much sooner than expected, even though the device still charges. A 850mAh battery in a big puff kit will need charging more often than a small device, but a battery that drops in a few draws is a different fault.
Common Causes
Long or frequent draws use more battery than short, occasional draws, and a mesh coil device uses more power when it is used heavily. A battery that is charged with a weak adapter, or that is topped up for a few minutes at a time, can show a full screen level that falls fast. A pod that is worn, or that gives weak vapour, can make a user draw harder and longer, which uses more battery. A device that is older, or that has been charged many times, can also hold less charge than a new device.
How to Fix
Charge the device fully with a trusted wall adapter until the screen shows a full battery, and avoid judging battery life from a short top up. Take slow, steady draws, with a gap between draws, and check the screen battery level over a day, rather than after a few draws. Check the pod age and liquid level, because a worn pod can make you draw more. Clean the contacts and refit the pod assembly, so the device does not waste power on a poor connection.
When to Replace
Replace the pod if battery drain stays fast on a fresh pod, with a full charge and normal draws, and the old pod was worn or low on liquid. Replace the device if battery drain stays fast on a fresh pod, with a full charge from a trusted adapter, clean contacts, and normal draws, and the screen shows a falling level much sooner than expected.
10. HQD Glow Air 70K Auto-Firing or Getting Hot
Auto-firing is when the device fires on its own, without a draw, or keeps firing after you stop drawing. Getting hot is when the device feels hot in a pocket, in a bag, or in your hand, even when you are not using it. This section is left exactly as a stop and replace section, for safety, and it does not give steps to keep using a device that fires on its own.
Common Causes
A device that fires on its own may have a damaged sensor, a damaged pod, liquid on the contacts, or damage from a drop, water, or heat. A device that gets hot may have a damaged battery, a damaged pod, or a fault in the firing sensor. A pod that is not fully seated, or that has leaked heavily, can also cause a device to behave badly, but the cause does not change the action.
How to Fix
Stop using the device at once. Do not charge it, do not draw from it, and do not try to fix it by removing and refitting pods, wiping contacts, or changing the slider. Keep the device away from heat, do not put it in a pocket or bag, and do not leave it on charge. If the device is hot, let it cool in a safe place, away from flammable items, and do not touch it if it is swollen, cracked, or smells of burning plastic.
When to Replace
Replace the device at once if it fires on its own, keeps firing after you stop drawing, or gets hot without use. Do not reuse the device, even if it stops firing on its own later. A pod from a device that auto-fired should not be reused in another device, and the device should be disposed of under local electronic waste rules, not in normal household waste.
FAQS (FREQUENTLY ASKED QUESTIONS)
Why is the HQD Glow Air 70K not hitting after charging?
Check the battery level on the OLED screen, then check pod seating, contacts, and seals. A full charge does not help if the pod assembly is not clicked in, if a seal is left on a new pod, or if the side in use is low on liquid. Charge fully, wipe the contacts, refit the assembly until it clicks, check the slider, and test with a fresh pod if you have one.
Why is the HQD Glow Air 70K not hitting after fitting a new pod?
Remove every seal from the new pod, including the silicone cap, the mouthpiece cover, the bottom sticker, and the pod base stickers, then slide the assembly in until it clicks. Give the new pod a short rest before the first draw, check the slider and the screen flavour indicator, and take a slow, steady draw. A pod that is not fully seated, or that has a seal left on, will not hit even if the battery is full.
Why does the HQD Glow Air 70K give mixed flavours?
Check the base slider first, then the screen flavour indicator. A slider left on the wrong side, or a slider that moved in a pocket, gives the flavour from that side. Slide firmly to the side you want, check the screen, and test both sides. If one side tastes mixed and the other tastes clean, the problem is with the side in use, not with the whole setup.
Why is one side of the HQD Glow Air 70K not working?
Check the liquid on the side in use, then slide to the other side and test it. One side can run low while the other still works, because each flavour pair is fed by its own pods and refill containers. Check that each refill container matches its correct pod slot, L or R, and refit the assembly until it clicks. Replace the pod on the side that stays silent after a liquid check and a refit.
Why is the HQD Glow Air 70K flashing?
Charge the device fully, then remove the pod assembly, wipe the contacts, and refit it until it clicks. Flashing can come from a low battery, a pod that is not fully seated, or a pod that is finished. If flashing clears with a fresh pod, the old pod was the cause. If flashing stays with a fresh pod and a full battery, the device needs replacement.
How long does the HQD Glow Air 70K take to charge?
The listings checked for this kit do not give a single official full charge time, so this guide does not give a single minute guarantee. Use a trusted USB-C cable and a trusted wall adapter, and charge until the OLED screen shows a full battery. Judge charging by the screen, not by the clock alone, and try a different trusted cable and adapter if the screen shows no charging sign.
Can the HQD Glow Air 70K be refilled with a bottle?
No. This kit is a prefilled pod kit, not a user refillable kit. The pods and refill containers are sealed, and the kit is not filled with a bottle by the user. When a pod is finished, replace it with a HQD Glow Air 35K replacement pod. Never open, pierce, or try to refill a sealed pod or refill container.
Can the coil in the HQD Glow Air 70K be replaced on its own?
No. The 1.1 ohm mesh coil is built into the pod, and it is not replaced on its own. When the coil wears, the flavour fades, vapour weakens, or a burnt taste appears, and the pod is replaced as a whole. Never try to remove or repair the coil inside a pod.
Why is the HQD Glow Air 70K stuck on one flavour?
Check the base slider and the screen flavour indicator. Slide firmly to the other side, and see if the screen changes. If the screen changes but the flavour does not, check the liquid on the new side, and refit the pod assembly. If the slider moves but the screen never changes, and a fresh pod test does not fix it, the device needs replacement.
How should the HQD Glow Air 70K be stored?
Store the device upright, in a cool, dry place, away from direct sunlight, heat, and water, and out of reach of children. Keep it out of a pocket or bag where the slider can move or the device can be damaged. Dispose of used pods and a finished device under local electronic waste rules, not in normal household waste.
