The Lost Mary Nera 30K Fullview is a rechargeable prefilled pod kit with two pods and two flavours at a time, and that dual pod system is the key to most faults. You keep the battery device, and you replace the pods when they run out. It is not a sealed disposable that you throw away when it stops, and it is not a kit you fill yourself with a bottle. A fault that looks like a dead device is often just a pod that is not seated, a refill container that is empty on the side in use, or a mode that was changed by mistake.
Jump to Section
Lost Mary Nera 30K Fullview at a Glance: A Dual Pod Prefilled Kit, Not a Disposable
Two Pods, Two Modes, One Display
Lost Mary Nera 30K Fullview Problems in One Quick Look
Fixing the Lost Mary Nera 30K Fullview, One Problem at a Time
Lost Mary Nera 30K Fullview at a Glance: A Dual Pod Prefilled Kit, Not a Disposable
| Entity / feature | What it is on the kit |
|---|---|
| Brand | Lost Mary |
| Product | Lost Mary Nera 30K Fullview Prefilled Pod Kit, also written Lost Mary Nera 30000 Fullview in some listings |
| Device type | Rechargeable prefilled pod kit, NOT a sealed disposable, NOT user refillable |
| Puff rating | Up to 30,000 puffs per full kit, an approximate maker rating that varies with draw length, frequency, and mode |
| Battery | 800mAh built-in, rechargeable by USB-C, see the battery note below |
| Pod and refill total | 24ml in total per full kit in most listings, 2 x 2ml prefilled pods plus 2 x 10ml refill containers, see the liquid note below |
| Nicotine strength | 20mg per ml (2 percent) nicotine salt (MaryLiq) in most listings, see the nicotine note below |
| Coil | Mesh coil built into each pod, not replaceable on its own, resistance not given in the listings checked |
| Flavours per setup | Two pods at a time, dual-flavour editions put a different flavour in each pod, single-flavour options also exist, see the flavour note below |
| Firing | Draw activated, inhale to vape, no fire button in the listings checked |
| Draw style | Mouth to lung (MTL) in the listings checked |
| Display | Curved LED display showing battery level and e-liquid level in the most detailed listings, plus a visible e-liquid window |
| Modes | Normal and Turbo, switched with a button on the base in most listings, see the mode note below |
| Pod connection | Magnetic click-in, push the pod in until it clicks |
| Replacement pods | Lost Mary Nera 15K pod and refill packs only in the listings checked, each pod set up to 15,000 puffs |
| TPD position | Pod chamber within the 2ml pod limit, refill container within the 10ml container limit, and 20mg per ml maximum, as set out in UK rules |
The liquid total needs a clear note, because listings give two totals for the same kit. Most listings give 2 x 2ml plus 2 x 10ml, for 24ml in total. Vape.co.uk gives the same parts, two 2ml pods and two 10ml containers, but gives a total of 22ml. This guide uses 24ml as the working total, from the most listings and from the parts themselves, and it keeps the 22ml figure visible here, because that listing gives it.
The nicotine note is short. Most listings say the kit is filled with 20mg nicotine salt in both the pod and the container. One listing says the nicotine is in the 2ml pod, and the refill container is 0mg. This guide does not settle that point, because the listings disagree, and it tells you to check the pack label for the version you bought. The checks below work either way, because they judge a pod by liquid level and taste, not by a nicotine figure.
The flavour note is short. Vape.co.uk lists 10 dual flavours and 6 single flavours. VapeVerse lists 17 dual flavour options and 9 single flavour options. In the dual-flavour editions, each pod can carry a different flavour, and seven of the ten dual editions in one listing count put a different flavour in each pod. This guide does not give a single flavour count, because the listings differ, and it tells you to check the edition you bought.
The mode note is short. Most listings say a button on the base flips between Normal and Turbo modes. Vape.co.uk says to use the display screen to switch between Turbo and Normal. This guide names the button on the base as the working method, from the most listings, and it keeps the display method visible here, because that listing gives it. Check your device, and use the control that changes the mode on your display.
The battery note is short. The battery is 800mAh in every listing checked for this kit, so there is no battery conflict to keep. The charging time is a different matter, and it is covered in the charging section below, because listings give two times and no single guarantee.
Do not confuse this kit with the Lost Mary Nera 15K, which is the same device with one pod set, 12ml in total, and up to 15,000 puffs, or with the Nera Pureview, which has no display and a 1000mAh battery in one comparison, or with the Euphoria track’s different Lost Mary Nera Fullview 70K, which gives up to 70,000 puffs. This kit is the Fullview 30K, with two pod sets, and it uses Nera 15K pod and refill packs only. Pods for other models or other brands do not fit this device in the same way, and forcing a wrong pod can damage the connection and cause leaking. Check the device name on the pod before you buy.
Note on the box and the cable: VapeDeliver lists the box as the device, two prefilled pods, and a user manual, with a USB-C cable not included. Other listings say the same, so check your box before you assume a cable is included, and use a trusted cable you know works.
Two Pods, Two Modes, One Display
Check the pods, the mode, and the display before you assume a flavour or vapour fault. On the Lost Mary Nera 30K Fullview, the pods, the modes, and the display work as one system, so a mode mistake can look like a pod fault, and a pod fault on one side can look like a device fault.
How the Pods and Refill Containers Work Together
Each pod pairs a 2ml mesh pod with a 10ml auto-refill container, and the container feeds the pod as you vape, so you do not fill the pod yourself with a bottle. One pod can run low while the other still tastes full, so a side that gives almost nothing is not proof that the whole setup is finished. Check the liquid on the side in use, swap to the other pod, and see if that side gives full vapour. If both pods are low, the setup is finished, even if the battery device still charges and the display still lights up.
Reading the Curved LED Display
The curved LED display lights up with every inhale, and it shows battery level and e-liquid level in the most detailed listings. A display that shows a battery level is not a fault. A display that shows nothing after a full charge, a very low battery, or a liquid level that stays still after many draws is the real problem. Where a liquid level is shown, you can also look at the visible e-liquid window and see if liquid is still present, even before taste changes.
If the display shows a low battery warning that clears after a full charge, the fault was battery level, not a broken device. If the display stays blank, or shows a warning that does not clear after a full charge and a fresh pod test, the device needs replacement, not repeated refitting.
Lost Mary Nera 30K Fullview Problems in One Quick Look
| Problem | First thing to check |
|---|---|
| Leaking / gurgling | Pod seating, pod seal, container matching, draw strength |
| Not firing / pod not detected | Pod alignment, magnetic connection, battery, seals, contacts |
| Flashing / screen trouble | Battery, pod seating, contacts, damage |
| Weak vapour | Battery, liquid on the side in use, pod age, mode, draw length |
| Fast battery drain | Mode, draw length and frequency, charging habits, pod age, device age |
| Tight draw | Blocked inlets, pod seating, condensation, seals left on a new pod |
| Mixed flavours / one side not working | Pod fitted, liquid on the side in use, mode |
| Not charging | USB-C cable, adapter, port, display charging sign, damage |
| Burnt taste | Liquid on the side in use, pod age, draw speed, new pod rest |
| Auto-firing / getting hot | Stop using it at once, do not charge or reuse it |
Fixing the Lost Mary Nera 30K Fullview, One Problem at a Time
The kit can stop hitting, fail to charge, leak, flash, or taste burnt when a pod, the contacts, the liquid level, the mode, the battery, or the airflow has a problem. Basic checks can help identify the cause before a pod or device replacement is needed.
Basic pod check, do this first for any problem below, unless that section tells you to stop for safety: Make sure each pod is fully seated, with no gap and no wobble, and that each pod matches its correct flavour side. This is also how to use the kit correctly for the first time, and how to replace a pod correctly. Wipe the pod contacts and the device contacts with a dry tissue, check the liquid on the side in use on the display and in the window, check the mode on the display, charge the device fully until the display shows a full battery, and give a new pod a short rest before the first draw. If you have a fresh replacement pod, test with it. If a fresh pod works and the old pod does not, the old pod is finished, even if the device is fine. On a new pod, remove every protective film and silicone plug first, then push the pod in until it clicks magnetically into place.
If you also use the BM6000 kit, see the Lost Mary BM6000 Not Working guide.
1. Lost Mary Nera 30K Fullview Leaking or Gurgling
Leaking is when liquid appears outside the pod, on the device, or on your hands, and gurgling is when the draw sounds wet and vapour feels thin. A little condensation in the mouthpiece is not the same as a leak, and a hard pull can make both worse.
Common Causes
A pod that is not fully seated, or a pod that has not clicked magnetically into place, can leave a gap where liquid escapes. A damaged pod seal, or a pod that has been refitted many times, can also leak. Hard pulls pull liquid into the mouthpiece faster than the coil can heat it, and that liquid shows as gurgling. A device kept upside down, or in a hot pocket or bag, can also cause leaking, because heat and pressure push liquid out of the pod.
How to Fix
Remove the pod and wipe the pod, the device, and the mouthpiece with a dry tissue. Push the pod in until it clicks magnetically into place, with no gap and no wobble. Take slow, steady draws, rather than hard pulls, and keep the device upright. This leaking and gurgling fault is the same fault people describe as leaking. If the mouthpiece has condensation, wipe it dry and test again with a slow draw. Do not keep using a pod that leaks heavily, even if it still gives vapour.
When to Replace
Replace the pod if leaking or gurgling stays after a clean refit and slow draws, and the pod seal or container shows damage. Replace the device if a fresh pod leaks in the same way, with a fully seated pod and slow draws, and the device contacts or pod bay show damage.
For the UK government’s evidence review on vaping, including that in the short and medium term vaping poses a small fraction of the risks of smoking but is not risk-free, see Office for Health Improvement and Disparities.
2. Lost Mary Nera 30K Fullview Not Firing or Pod Not Detected
Not firing is when you draw and get nothing, or the device seems dead even though it charges. A pod not detected fault often shows by a complete lack of vapour, with no display change on a draw.
Common Causes
A pod that is not fully seated gives poor contact, so the device cannot detect the pod. Dirty contacts, condensation on the contacts, or a damaged pod can also cause a pod not detected fault. A battery that is very flat can leave the device dead on a draw, even if it shows a little life on charge. A protective film or silicone plug left on a new pod blocks contact, and a pod fitted in the wrong slot can also fail to fire on the side in use.
How to Fix
Charge the device fully until the display shows a full battery, then remove the pod and wipe the contacts with a dry tissue. Check that every protective film and silicone plug is removed from a new pod, then push the pod in until it clicks magnetically into place, with no gap and no wobble. Check the mode on the display, and take a slow, steady draw. Test with a fresh pod if you have one, because a fresh pod test settles a pod detection fault fast.
When to Replace
Replace the pod if the device fires with a fresh pod, but not with the old pod, after a full charge, a clean refit, and a seal check. Replace the device if it will not fire with a fresh pod, a full battery, and clean contacts.
3. Lost Mary Nera 30K Fullview Flashing or Screen Trouble
Flashing is when the display blinks, shows a warning, or goes blank, even though the device still charges. A screen fault is often a battery or pod seating fault, not a broken screen on its own.
Common Causes
A battery low on charge can cause flashing or a low battery warning on the display, and a battery that is very flat can leave the display blank. A pod that is not fully seated gives poor contact, so the device cannot read the pod, and the display can flash or stay blank. Dirty contacts, condensation on the contacts, or a damaged pod can also cause flashing. A device that has been dropped, or that shows damage, can flash even with a full battery and a fresh pod.
How to Fix
Charge the device fully with a trusted USB-C cable and adapter, and check the display again after a full charge. Remove the pod, wipe the contacts with a dry tissue, push the pod in until it clicks magnetically into place, and check the liquid level on the display and in the window. Take a slow, steady draw, and see if the display shows a battery level and a liquid level. If the display shows a battery level after a full charge and a clean refit, the fault was battery level or pod seating, not a broken screen.
When to Replace
Replace the pod if flashing or screen trouble clears with a fresh pod, after a full charge and a clean refit. Replace the device if flashing or a blank screen stays with a fresh pod, a full battery, and clean contacts, or if the device shows damage.
4. Weak Vapour From the Lost Mary Nera 30K Fullview
Weak vapour is when you get a thin draw, a small cloud, or a flavour that seems far away, even though the device still fires. Weak vapour on one side only is a pod or liquid fault, not a device fault.
Common Causes
A pod low on liquid gives thin vapour first, then almost nothing. A pod that has been used for many puffs, or that has been in the device for a long time, gives weak vapour as the coil and wick wear. A battery low on charge gives weak vapour, because the coil does not heat fully. A pod not fully seated, or a mode left on Normal when you expect Turbo, can also give weak vapour on the side in use, while the other side still works.
How to Fix
Charge the device fully until the display shows a full battery, then check the liquid level on the display and in the window. Remove the pod, wipe the contacts with a dry tissue, push the pod in until it clicks magnetically into place, and test again. Take a slow, steady mouth to lung draw. Give a new pod a short rest before the first draw, so the coil is fully primed and vapour is not weak from a dry start. This weak vapour fault is the same fault people describe as not hitting. If weak vapour stays on a fresh pod, the problem is not the old pod alone.
When to Replace
Replace the pod if weak vapour stays after a full charge, a full refit, and a test, and the pod has low liquid or many puffs on it. Replace the device if weak vapour stays on a fresh pod, with a full battery and a clean, fully seated pod.
5. Fast Battery Drain on the Lost Mary Nera 30K Fullview
Fast battery drain is when the display shows a falling battery level much sooner than expected, even though the device still charges. A battery that drops in a few draws is a different fault from normal use over a day.
Common Causes
Turbo mode uses more battery than Normal mode, and long or frequent draws use more battery than short, occasional draws. A battery that is charged with a weak adapter, or that is topped up for a few minutes at a time, can show a full display level that falls fast. A pod that is worn, or that gives weak vapour, can make a user draw harder and longer, which uses more battery. A device that is older, or that has been charged many times, can also hold less charge than a new device.
How to Fix
Charge the device fully with a trusted wall adapter until the display shows a full battery, and avoid judging battery life from a short top up. Switch to Normal mode for everyday use, and save Turbo mode for when you want a stronger hit, because Normal mode sips power and e-liquid and stretches the puff figure further. Take slow, steady draws, with a gap between draws, and check the display battery level over a day, rather than after a few draws. Check the pod age and liquid level, because a worn pod can make you draw more. Clean the contacts and refit the pod, so the device does not waste power on a poor connection. The Lost Mary Nera 30000 Fullview uses an 800mAh battery in every listing checked, and heavy use in Turbo mode will drain it faster than light use in Normal mode.
When to Replace
Replace the pod if battery drain stays fast on a fresh pod, with a full charge and normal draws, and the old pod was worn or low on liquid. Replace the device if battery drain stays fast on a fresh pod, with a full charge from a trusted adapter, clean contacts, and normal draws in Normal mode, and the display shows a falling level much sooner than expected.
6. Tight Draw From the Lost Mary Nera 30K Fullview
Tight draw is when you have to pull hard to get vapour, or you get almost nothing even though the device still fires. This kit is a mouth to lung device in the listings checked, so the draw is restricted by design, but a draw that gets much tighter than normal is a fault.
Common Causes
Blocked airflow inlets, lint or dust in the inlets, or condensation in the mouthpiece can make the draw feel tight. A pod that is not fully seated, or a pod with a film or plug left on, can also block the draw. A pod low on liquid, or a pod that has been used for many puffs, can give a tight, weak draw. A battery low on charge can also give a weak, tight feeling draw, because the coil does not heat fully.
How to Fix
Remove the pod and check the airflow inlets for lint, dust, or liquid, and wipe them with a dry tissue. Check that every protective film and silicone plug is removed from a new pod, then push the pod in until it clicks magnetically into place. Wipe the mouthpiece and the pod contacts, and take a slow, steady draw, rather than a hard pull. If the draw stays tight, check the display battery level, because a low battery can also give a weak, tight feeling draw.
When to Replace
Replace the pod if the draw stays tight after cleaning, seal checks, and a full refit. Replace the device if the draw stays tight on a fresh pod, with clean inlets and a fully seated pod.
7. Mixed Flavours or One Side Not Working on the Lost Mary Nera 30K Fullview
Mixed flavours are when you taste the wrong flavour, or both flavours at once, and one side not working is when one flavour gives vapour and the other gives almost nothing. On a dual pod kit, this is usually a pod or liquid fault, not a device fault.
Common Causes
A pod fitted in the wrong slot gives the flavour from that slot, and it can look like a mixed flavour fault. A side that is low on liquid gives weak or mixed taste, while the other side still tastes full, because each side has its own pod and container. A pod that is not fully seated on one side, or a pod that has not clicked magnetically into place, can also cause one side to stay silent. A worn pod on one side gives fading taste on that side only.
How to Fix
Check the pod fitted on each side first, then the display. Swap to the other pod and test it, check the liquid on the side in use, and see if that side gives full vapour. If one side tastes mixed and the other tastes clean, the problem is with the side in use, not with the whole setup. Refit the pod on the silent side until it clicks magnetically into place, with no gap and no wobble, and check that it matches its correct flavour side.
When to Replace
Replace the pod on the side that stays silent or mixed after a pod check, a liquid check, and a clean refit. Replace the device only if both sides stay silent or mixed with fresh pods, a full battery, and clean contacts.
8. Lost Mary Nera 30K Fullview Not Charging
Not charging is when the device shows no charging sign on the display, or the battery level does not rise, even though it is plugged in. A charging fault is often a cable or port fault, not a dead battery on its own.
Common Causes
A weak or damaged USB-C cable, a weak wall adapter, or a laptop port that does not give enough power can all cause not charging. Lint or dust in the charging port can block the cable, and a cable that is not pushed fully in can also fail to charge. A battery that is very flat can take a short time before the display shows a charging sign, so a charge judged in the first minute can look like a fault. A device with port damage, or with liquid in the port, can also fail to charge.
How to Fix
Use a trusted USB-C cable you know works, and a trusted wall adapter, and plug the device in directly from a wall socket, not from a weak laptop port. This is how to charge the kit correctly, and it is the first fix for not charging. Push the cable fully into the port, check for lint or dust with a dry tissue, and look for a charging sign on the display. Leave the device on charge and check the display again after a short time, rather than judging it in the first minute. Try one different trusted cable and one different trusted adapter, and if a cable works for another device but not for this kit, change the cable and the adapter together, not just one of them. The cable is not included in the box in the listings checked, so a trusted cable you already own is the right cable to test with.
When to Replace
Replace the cable and adapter first if the device charges with a different cable and adapter. Replace the device if it will not charge with a trusted cable and adapter, a clean port, and a full charge time, and the display shows no charging sign.
9. Burnt Taste From the Lost Mary Nera 30K Fullview
Burnt taste is when vapour tastes harsh, dry, or like burnt cotton, even though the device still fires. Burnt taste is a sign that the coil is dry or worn, not a sign that the device needs a stronger draw.
Common Causes
A pod low on liquid, or a refill container that is empty on the side in use, leaves the coil dry, and a dry coil burns on a draw. A new pod used straight away, with no short rest before the first draw, can also taste burnt, because liquid has not reached the coil evenly. Hard, long draws, one after another with no gap, can dry the coil faster than liquid can reach it. A pod that has been used for many puffs gives burnt taste as the coil and wick wear, even if liquid is still present. Turbo mode can also dry a coil faster, because it uses more power and more liquid.
How to Fix
Check the liquid on the side in use first, then swap to the other pod and see if that side tastes clean. Give a new pod a short rest before the first draw, so the coil is fully primed and vapour is not burnt from a dry start. Take slow, steady draws, with a gap between draws, rather than hard pulls one after another, and switch to Normal mode if Turbo mode tastes burnt. If burnt taste stays on one side only, the problem is with that side, not with the whole setup.
When to Replace
Replace the pod if the burnt taste stays after a liquid check, a rest, and slow draws, and the pod has low liquid or many puffs on it. Do not keep using a pod that tastes burnt, because a burnt coil will not recover. Replace the device if a fresh pod tastes burnt straight away, after a rest and slow draws, with a full battery and a fully seated pod.
10. Lost Mary Nera 30K Fullview Auto-Firing or Getting Hot
Auto-firing is when the device fires on its own, without a draw, or keeps firing after you stop drawing. Getting hot is when the device feels hot in a pocket, in a bag, or without use. This section is stop and replace only, with no fix steps that keep a faulty device in use.
Common Causes
Liquid in the pod bay, a damaged pod, or a device that has been dropped can cause auto-firing, because the draw sensor or the pod connection no longer reads correctly. Heat in a pocket or bag, or a device left in direct sunlight, can also make a device feel hot, and a device that fires on its own will also get hot from repeated firing.
How to Fix
Stop using the device at once. Do not charge it, do not draw from it, and do not try to fix it by removing and refitting pods, wiping contacts, or changing anything else. Keep it away from flammable material, and do not put it in a pocket or bag again. If it feels very hot, swollen, or smells of burning plastic, keep it away from people and pets, and follow local electronic waste rules for a damaged device.
When to Replace
Replace the device at once if it fires on its own, keeps firing after you stop drawing, or gets hot without use. Do not reuse the device, even if it stops firing for a short time, because the fault can return without warning.
FAQS (FREQUENTLY ASKED QUESTIONS)
Why is the Lost Mary Nera 30K Fullview not hitting after charging?
Check the display battery level, then check pod seating, contacts, and plugs. A full charge does not help if the pod is not seated, if a film or plug is left on a new pod, or if the pod is low on liquid. This is the answer for not hitting after charging. Charge fully, wipe the contacts, refit the pod until it clicks, and test with a fresh replacement pod if you have one.
Why is the Lost Mary Nera 30K Fullview not hitting after fitting a new pod?
Remove every protective film and silicone plug from the new pod, then push the pod in until it clicks magnetically into place. Give the new pod a short rest before the first draw, check the mode on the display, and take a slow, steady draw. A pod that is not fully seated, or that has a plug left on, will not hit even if the battery is full.
How do you switch flavours on the Lost Mary Nera 30K Fullview?
Swap the pod to the flavour you want, because each pod carries its own flavour. In dual-flavour editions, each pod can carry a different flavour, so swap pods to change flavour, with no refilling and no bottle. Check the display and the liquid level on the side in use, and take a slow draw before you judge the flavour.
How do you change the pod on the Lost Mary Nera 30K Fullview?
Pull the old pod straight out of the device. Remove every film and plug from the new pod, align it with the pod slot, and push it in until it clicks magnetically into place, with no gap and no wobble. Give the new pod a short rest before the first draw, and check the mode and the display.
How do you switch between Normal and Turbo mode on the Lost Mary Nera 30K Fullview?
Use the button on the base to switch between Normal and Turbo, in most listings, and check the mode on the display. One listing says to use the display screen to switch, so check your device and use the control that changes the mode on your display. Normal mode sips power and liquid for longer sessions, and Turbo mode boosts vapour and flavour but uses battery and liquid faster.
Can you refill the Lost Mary Nera 30K Fullview pods?
No. This kit is a prefilled pod kit, not a user refillable kit. The pod and refill container are sealed, and the kit is not filled with a bottle by the user. When a pod is finished, replace it with a Nera 15K pod and refill pack. Never open, pierce, or try to refill a sealed pod or refill container.
How long does it take to charge the Lost Mary Nera 30K Fullview?
Most listings give no single minute figure, so this guide does not give a single minute guarantee. One review says just under 45 minutes from 0 percent, and another listing count says around 30 minutes, so the listings themselves disagree. Use a trusted USB-C cable and a trusted wall adapter, and charge until the display shows a full battery. Judge charging by the display, not by the clock alone.
How many puffs does the Lost Mary Nera 30K Fullview give?
The Lost Mary Nera 30000 Fullview gives up to 30,000 puffs per full kit in the listings checked, also written as 30000 in some listings. That figure is approximate, not a guarantee, and actual use varies with draw length, frequency, and mode. Each pod set gives up to 15,000 puffs in the listings checked, so a pod used alone will not reach the full figure, because the figure reflects the full kit, with both pod sets.
What pods work with the Lost Mary Nera 30K Fullview?
Only Lost Mary Nera 15K pod and refill packs. Pods for other models or other brands do not fit this device in the same way, and forcing a wrong pod can damage the connection and cause leaking. Check the device name on the pod before you buy.
How should you store the Lost Mary Nera 30K Fullview?
Store the device upright, in a cool, dry place, away from direct sunlight, heat, and water, and out of reach of children. Keep it out of a pocket or bag where the device can be damaged. Dispose of used pods and a finished device under local electronic waste rules, not in normal household waste.
